Press Read ECU Info button, and wait about 10 seconds. Switch ON ignition with the key which you want to test! Start software, select VDO NEW – CAN bus from menu, and press Transponder Check.
The new key is already stored into immobiliser and you can start engine! If the immobiliser’s warning lamp on the dash is still flashing, there is some error in programming procedure, you can check the transponder key- see how to do this on the next picture!Ĩ. If you have switched ON ignition with key which is already programmed by TMPro, the warning lamp of immobiliser on the dash will be turned off. This picture shows the final Vagtacho window. The dash will be reset, and the programming procedure will be completed! This is the last step, after this the new data will be written into immobiliser! If you have marked and erased some keys, they will NOT works anymore!ħ. After pressing Continue Vagtacho will writes the data into immobiliser after few seconds. If you press Cancel nothing will happens, and the data won’t be written into immobiliser. If you are sure that everything is all right, press Continue, otherwise press Cancel. Press Write Keys and the warning window will be open. Press Write Keys to complete programming procedure !Ħ. Now you are ready to program the new transponder key into the immobiliser. If everything is ok, Vagtacho will add the new key into the data of immobiliser and will show ID number of new key on screen. If this key is already programmed to the car, or it is from another car, Vagtacho will show warning message on screen and won’t program this key!ĥ. Switch ON ignition with key which you want to program! The key may be new – already programmed with TM Pro, or old – key which has been used with the same car! Vagtacho will check the key. Press Add Key and a message will be shown. Insert transponder key with new Megamos ID48 chip and program it.Ĥ. Insert the new key in TMPro box and program it.ģ. TMPro will check file and will open a menu where you can program new transponder key for this car. Start TMPro and upload that file in software. After you had saved file, press Close – Disconnect, switch iginiton off and remove key. Press Save Data to File and save immobiliser’s data somewhere in you computer. ID numbers of the transponders which are stored into memory will be show.Ģ.
Press Program New Key, software will read data from the dash and after few seconds a new window will be open. Press Connect Selected ECU button, after 5 seconds the data of the dash will be shown on screen. Start software, select VDO NEW – CAN bus from menu. Switch ON ignition with any key new or old, no mater which one. Inca with VDO or Motometer 1997 -2000(mileage change only)Ī3,TT,A6 Magnetti Marelli dash 1998 – 2003Ī4 Bosch dash 2000 – 2008 – Read/write of encrypted data with V4.5!Ī4,A6,A8 1995-1999 (immo box – read pin code) How to programmer keys with vag tacho interface?ġ. Leon, Toledo, Cordoba, Ibiza with VDO or Motometer dash 1997-2003Īlhambra with VDO 2000 – 2004(mileage change only)
Gol ( Kostal immo box) 1999-2003 (pin code read only)Īltea, Leon, Toledo with VDO 2003 – 6/2006 LT35 ( Temic immo box) 1999-2003 (pin code read only) Sharan with VDO dash: 2000-2004(mileage change only)Ĭaddy, Lupo with VDO or Motometer dash 1997 – 2002(mileage change only) Polo with VDO or Motometer dash: 1999-2006 (1999-2002 mileage change only) Passat, Jetta, with VDO, Marelli or Motometer dash: 1997-2004
Golf 4, Bora with VDO or Motometer/Bosch dash: 1997-2003
Golf 5, Caddy, Touran, Jetta, EOS with VDO dash 2003 – June.2006 Golf 6, Jetta, Polo, EOS with VDO dash 2009 – 2011, note: not all dashes are supported! VAG TACHO USB V5.0 Supported vehicles List: Read PIN Code,Programming new keys(TP22,23,24,25 transponders are required!) NEW key programming feature for VAG cars with VDO dashes on CAN bus! (TP2 and UDS protocols) VAG TACHO USB Cable Main functions: Pre-programming of TP2x transponders as dealer’s keys with component security data which is read from immobiliser!
īuilt-in programmer for Megamos ID48 transponders! Main work for CAN and K-line,specially support VDO with 24C32 or 24C64. VAG TACHO USB V5.0 is one cheap and powerfully Interface that change Mileage and programming keys for VW,Audi,Skoda and Seat till 2011 Year.